AMS programmable logic controller (PLC) boards that are compatible with the plc Delta Electronics ES2 series. The PLC is capable of measuring and controlling various inputs and outputs and is specifically designed to work with the Delta ES2 series of devices.

The high-speed input of 2 channels at 100 kHz and 6 channels at 10 kHz suggests that the PLC is capable of collecting and processing data from multiple sources at different speeds.

The single phase input of 8 points and AB phase input of 4 groups implies that the PLC can measure and control the electrical phases of an AC power supply.

The high-speed comparison interrupt of 8 points indicates that the PLC has the ability to interrupt the normal processing of the system based on certain conditions.

The communication port of 1*RS232 and 2*RS485 suggests that the PLC has multiple ports for communication with other devices or systems, which provides flexibility and scalability in terms of connecting to other devices.

The ability to connect 8 expansion modules further suggests that the PLC can be expanded to accommodate additional inputs and outputs as needed.

Additionally, the support for S-curve acceleration and deceleration functions and inverter control commands indicates that the PLC is capable of controlling and adjusting the speed of motor-driven systems.

Model	PLC16ESR/T	PLC24ESR/T	PLC32ESR/T	PLC40ESR/T	PLC60ESR/T
Input	8	16	16	24	36
Output	8	8	16	16	24
L	105	126	145	165	225
L1	97	115	137	157	217

Parameter

Power supply voltage	24VDC/100-240VAC(-15%-10%)
Connection method	Drop-off European terminal block (distance between endpoints: 5MM)
Operation specifications	When the power supply slowly rises to 95~100VAC, the PLC starts to move, and when the power supply drops slowly to 70VAC, the PLC stops its action. The power supply will continue to run within 10MS of instantaneous power failure.
Power fuse capacity	2A/250VAC
Power consumption	30VA
DC24V current output*1	500MA
Power protection	DC24V output with short circuit protection
Surge voltage tolerance	1,500VAC (PRIMARY-SECONDARY), 1,500VAC(PRIMARY-PE) 500VAC(SECONDARY-PE)
Insulation resistance	Above 5Q (500VDC between all output/input points and ground)
Interfere with immunity	ESD(IEC 61131-2JEC61000-4-2):8KV AIR DISCHARGE EFT (IEC 61131-2, 61000-4-4): POWER LINE: 2KV, DIGITAL /0: 1KV, ANALOG& COMMUNICATION/O: 1KV RS (IEC 61131-2,LEC 61000-4-3): 26MHZ-1GHZ,10V/M
Grounded	The wire diameter of the grounding wiring shall not be less than the wire diameter of the power terminal L and N (When multiple PLCs are used at the same time, be sure to ground at a single point)
Operating/storage environment	Operation 0℃-55℃ (temperature), 5-95% (humidity) Pollution degree 2 Storage: 25℃-70℃ (temperature), 5-95% (temperature)

Analog module input/output (number of channels * resolution) configuration

Model	DVP04AD-E2	DVP04DA-E2	DVP06XA-E2	DVP02DA-E2	DVP04TC-E2	DVP04PT-E2
Input	AD1-4(4CHx14-bit)	–	AD1-4(4CHx14-bit)	–	CH1-4(4CHx16-bit)	CH1-4(4CHx16-bit)
Output	–	DA1-4(4CHx14-bit)	DA1-2(2CHx14-bit)	DA1-2(2CHx14-bit)	–	–

element	rang
X external input relay	X0-377, 256 points, octal code (*4)
Y external output relay	Y0-Y377, 256 points, octal code (*4)
M auxiliary relay for general use	M0~M511,512 points (1) M768~M999, 232 points (1) M2000-M2047, 48 points (*1)
M auxiliary relay power failure retention use	M512~M767, 256 points (2) M2048-M4095, 2,048 points (2)
M auxiliary relay for special use	M1000~M1999,1,000points (partially maintained after power failure)
T Timer 100ms (M1028=ON,T64~T126为10ms)	T0~T126,127 points(1) T128-T183,56 points(1) T184~T199 subroutines with 16 points (1) T250~T255],6-point accumulation type (1)
T Timer 10ms(M1038=ON,T200-245为1ms)	T200-239,40points(1) 【T240~T245】,6 points Cumulative(1)
T Timer 1ms	T127,1 points (1) 【T246-T249】,4 points Cumulative(*1)
C counter 16-bit upper number	C0-111,112 points(1) C112-C127,16 points (2) C128-C199，72 points(*1)
C counter 32-bit up/down the number	C200-C223,24 points(1) C224-C232,8 points(2)
C counter 32-bit high-speed counter	C235-C244,1 phase 1 input,,10 points (2) C245-C250,1 phase 2 input,,6 points (2) C233,C234,C251-C254,2 phase 2 input,,7 points(*2)
S step point initial step point	S0-S9,10 points(*2)
S step point for home return	S10-S19,10 points(used with ST command)(*2)
S Step point For power failure retentive	S20-S127,108 points(*2)
S step point Generally use	S128-S911,784 points(*1)
S Step point for alarm	S912-S1023,112 points(*2)
T timer current value	T0-255,16-bit timer256 points
C Counter current value	C0~C199,16-bit counter 200 points C200-C254,32-bit counter 55 points
D data registers generally use	D0-D407,408 points,(1) D600-D999,400 points(1) D3920~D9899,5,980 points(*1)
D Data register for power failure retention	D408-D599,192 points(2) D2000-D3919,1,920 points(2)
D Data register For special register	D1000-D1999,1,000 points (Some are maintained after power failure)
D Data register for special modules	D9900-D9999,100 points(1)(5)
D Data register for indirect designation	E0-e7, f0-f7.16 points(*1)
N Master Reuse	n0-n7,8 points
P CJ, the CALL instruction	P0-P255,256 points
I interrupt External interrupt insertion	I00口(X0),I10口(X1)I20口(X2) I30口(X3),I40口(X4),I50口(X5), I60口(X6),I70口(X7),8 points (口=1,trigger on rising edge,口=0,trigger on falling edge)
I interrupt Timed interrupt insertion	I6口口,I7口口,(口口-05~99ms),2 points
I interrupt High-speed counting reaches interrupt insertion	I010、I020、I030、I040、I050、I060、I070、I080,8 points
I interrupt communication reception interrupt insertion	I40(COM1)、I150(COM2)、I60(COM3)(*3),3 points
Constant K decimal	K-32,768-K32,767(116-bit operation) K-2,147,483,648~K2,147,483,647(32-bit operation)
Constant H hexadecimal	H0000- HFFFF(16-bit operation) H00000000 -HFFFFFFFF-(32-bit operation)

*1 Non-latched area, cannot be changed
*2 The latched area cannot be changed
*3 COM1 is the built-in RS-232 communication port, COM2 and COM3 are the built-in RS-485 communication ports
*4 When the number of digital input expansion X points is extended to 256 points, the output Y can only use 16 points. On the contrary, when the output Y points are extended to 256 points, the input X can only use 16 points.
*5 This area will be valid only when the host is connected to an analog module, and each connected analog module will occupy 10 points

Power-off hold action

Memory type	Power OFF→ ON	STOP→RUN	RUN→STOP	M1031 non-maintained areas are all cleared	The M1032 power failure retention area is all cleared	Factory setting value
Non-power failure retention	Clear	No change	When M1033 is OFF, clear When M1033 is ON, no change	Clear	No change	0
power failure retention	No change	No change	No change	No change	Clear	0
Special M, Special D indirectly designated register	Initial value setting	No change	No change	No change	No change	Initial value setting